Thermaltake Water 3.0 360 ARGB Sync Edition comes with three 120 mm fan with a large surface radiator, high
performance waterblock and pump for ultimate CPU cooling. The built-in Pure ARGB fan features compression blades,
hydraulic bearing, and 16.8 million colors LEDs that is ready to sync with 5V RGB capable motherboards from Asus,
Gigabyte, MSI and AsRock. Users can easily switch RGB lighting effects using the ARGB controller that is included in
the packet, or by ASUS Aura Sync, GIGABYTE RGB Fusion, MSI Mystic Light Sync and AsRock Polychrome software. Water
3.0 ARGB Sync Edition Series allows users to enjoy better cooling performance and greater CPU protection!
Tt LCS Certified is a Thermaltake exclusive certification applied to only products that pass the design and hardcore enthusiasts standards that a true LCS chassis should be held to. The Tt LCS certification was created so that we at Thermaltake can designate to all power users which chassis have been tested to be best compatible with extreme liquid cooling configurations to ensure you get the best performance from the best features and fitment.
Water 3.0 ARGB Sync Edition is equipped with Thermaltake Pure 12 ARGB Sync Radiator Fan. It features compression
blades, hydraulic bearing, and a 16.8 million colors LED ring with 9 addressable LEDs that is ready to sync with 5V
RGB capable motherboards from Asus, Gigabyte, MSI and AsRock.
The ARGB controller allows users to switch LED modes, LED colors, and LED Speeds when using a
motherboard without a
5V addressable RGB header. Users can switch between flow, ripple, pulse, blink, wave, full light, RGB
spectrum, and
off modes with various colors and LED speeds options.
*The maximum signal output for one controller is 90 addressable LEDs.
Specially designed for Water 3.0 ARGB Series, the large surface radiator increases the cooling surface
and
exceptional heat dissipation.
The high performance copper base plate accelerates the heat conductivity. The pre-refilled coolant reduces any stress from liquid replenishment hassle. Additionally, the reinforced sleeved cable delivers the best durability and prevents the tubing from any damages.
The high quality and reliable pump enables the maximum amount of water circulation, keeping the copper
plate
continuously cool. The low evaporation tube effectively decreases the loss of coolant; therefore, no
refill is
required.
Featuring the latest cooling performance, the self-contained design of the Thermaltake Water 3.0 ARGB
Sync Edition
Series provides an easy installation system and a totally maintenance-free operation, requiring only
the minimum
amount of space in the chassis.
Sync with Motherboard RGB Software
Designed to synchronize with ASUS Aura Sync, GIGABYTE RGB Fusion, MSI Mystic Light Sync, and ASRock Polychrome. It supports motherboards with a 5V addressable RGB header, allowing you to control the lights directly from the software mentioned above without installing any extra lighting software or controllers. For more details, please visit ASUS, GIGABYTE, MSI, and ASRock official websites.
-
Aura Addressable Header
ASUS -
Digital Pin Header
GIGABYTE -
JRAINBOW Header
MSI -
Addressable RGB LED Header
ASRock
Category | Caution |
---|---|
Chassis, ARGB Fan, ARGB AIO |
|
RGB Memory, VGA Waterblock, Distro Plate |
|
Cautions
Thermaltake recommends the following steps to be taken before using the Pacific series radiators and water blocks:
- To ensure a clean loop, flush and rinse your radiators and water blocks with distilled water prior to use.
- Do not use tap water or distilled water as your coolant, it may harm your loop and reduce performance.
- It is strongly recommended to use market-proven pre-mix coolant, such as Thermaltake Coolant 1000, which offers great performance while protecting the entire liquid loop from corrosion.
- Before storing your water cooling components, please clean, rinse, and dry. This will ensure a longer lifespan for your components.
Thermaltake recommends the following steps to be taken after completing your water loop setup:
- It is strongly recommended to use market-proven pre-mix coolant, such as Thermaltake Coolant 1000, which offers great performance while preventing corrosion in the entire cooling system (copper, brass, nickel, aluminum, and steel).
- Fill the reservoir with coolant and cycle the power on and off several times while the pump pushes the coolant into the loop.
- DO NOT let the pump run dry. If no liquid is entering the pump, turn off your power immediately.
- Fill the reservoir to the top to prevent air from entering the pump.
- If necessary, tilt the system slightly from side to side to bleed the air out of the loop.
- Place paper towels under fittings and joining points to test for leaks.
- Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop.
- Before starting, flush out your system properly to prevent any coolant or unwanted particles from sticking to your tubes, radiators, and other cooling components.
- Coolant might fade over time.
P/N | CL-W234-PL12SW-A |
---|---|
重量 | 2250 g |
Pump |
Motor Speed: 3600 RPM Rated Voltage: 12 V & 5V Power Input: 12V – 3.9 W , 5V – 1.06 W |
Water Block | Material: Copper |
Fan |
Dimension: 120 x 120 x 25 mm Speed: PWM 500~1500 R.P.M (2510-4PIN) Noise Level: 25.8 dB-A Power Input: 12V- 1.44 W, 5V – 1.6W (one fan) Rated Voltage: 12 V & 5V Max. Air Flow: 56.45 CFM Max. Pressure: 1.59 mm-H2O LED Control: ARGB controller or 5V addressable RGB header on motherboard |
Tube |
Length: 400 mm Material: Rubber |
Radiator | Dimension: 394 x 120 x 27 mm |
Compatibility |
Intel LGA 2066/2011-3/2011/1700/1200//1156/1155/1151/1150 AMD FM2/FM1/AM5/AM4/AM3+/AM3/AM2+/AM2 *AIO Cooler bracket adapter comes in the AMD Threadripper CPU box. |
User Manual
- ファイル名
- 概要
- サイズ
- Version
- Release Date