Pacific MX2 Ultra CPU Waterblock Pacific MX2 Ultra CPU Waterblock Pacific MX2 Ultra CPU Waterblock Pacific MX2 Ultra CPU Waterblock Pacific MX2 Ultra CPU Waterblock Pacific MX2 Ultra CPU Waterblock
Pacific MX2 Ultra CPU Waterblock

Pacific MX2 Ultra CPU Waterblock

在庫あり
P/N
CL-W332-CU00SW-A
USD$174.99
Pacific MX2 Ultra has a 2.1 Inch LCS Display that presents real-time information and even plays JPG and GIF files with 480*480 resolution, bringing great visual aesthetics and highly customizable functions to your water block.

2.1 Inch LCD Display

Pacific MX2 Ultra has a 2.1 Inch LCS Display that presents real-time information and even plays JPG and GIF files with 480*480 resolution, bringing great visual aesthetics and highly customizable functions to your water block.

Central Inlet Design

Pacific MX2 Ultra incorporates a central inlet design which not only allows coolant to contact the CPU heat source directly but to have a more effective waterflow, thus ensures the best possible cooling performance.

Caution: Due to the central inlet design, the inlets and outlets are restricted to a specific direction. (See here)


Built-in Water Temperature Sensor

The Pacific MX2 Ultra CPU Water Block features a built-in temperature sensor that will pick up the temperature from the passing coolant and transmits the signal to the TT RGB Plus software, allowing users to monitor current temperature immediately.

Supports Intel LGA 1700 Socket

The Pacific MX2 Ultra CPU Water block now supports the latest Intel LGA 1700 Socket, which allows users to stay in the latest trends. It also supports Intel and AMD universal brackets, allowing different CPU users to enjoy fantastic lighting effects after a quick installation.

Compatibility list:
Intel: LGA 2066/2011/1700/1200/1156/1155/1151/1150
AMD: AM5/AM4/AM3+/AM3/AM2+/AM2



Fully Customizable with TT RGB Plus 2.0

Monitor frequency and real-time temperature directly from our 2.1 inch LCD Display. There’s also six preset GIFs for you to choose, or upload any image or GIF file to add extra flair with the TT RGB Plus 2.0 software.
Caution: Pacific MX2 Ultra is only supported by the TT RGB Plus 2.0.


Check out more animated GIFs for your AIO displays here.

Start-up & Standby Screen Setting

TT RGB Plus 2.0

最新バージョンのTT RGB Plus2.0を使用することで、CPU情報、水温などのシステム情報をリアルタイムにモニタリングすることができます。

注意:
TT RGB Plus2.0とTT RGB Plus1.0は互換性がないため、1つを選んでダウンロードしてください。

今すぐダウンロード マニュアルをダウンロード

Works with Amazon Alexa

All Thermaltake TT RGB PLUS products support Amazon Alexa Voice Service, allowing you to give voice commands to the Alexa-enabled devices.

LEARN MORE

TT AI Voice Control

Give you full control over the TT RGB PLUS products with your voice. “SyncALL, Say”Hello TT”.

Note: TT AI Voice control and Amazon Alexa requires the use of at least one TT RGB PLUS software-enabled product to function.

Cautions

Thermaltake recommends the following steps to be taken before using the Pacific series radiators and water blocks

  • To ensure a clean loop, flush and rinse your radiators and water blocks with distilled water prior to use.
  • Do not use tap water or distilled water as your coolant, it may harm your loop and reduce performance.
  • It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while protecting the entire liquid loop from corrosion.
  • Before storing your water cooling components, please clean, rinse and dry. This will ensure a longer lifespan for your components.

Thermaltake recommends the following steps to be taken after completing your water loop setup

  • It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while preventing the entire cooling system – copper, brass, nickel, aluminum, and steel – from corrosion.
  • Fill the reservoir with coolant and cycle the power on and off several times while the pump pushing the coolant into the loop.
  • DO NOT let the pump run dry, when there is no liquid entering the pump turn off your power immediately
  • Fill the reservoir to the top as it will prevent air from going into the pump
  • If necessary tilt the system slightly from side to side to bleed the air out of the loop.
  • Place some paper towels under fittings and joining points to test for leaks.
  • Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop.
  • Before starting, flush out your system correctly to prevent any coolant or unwanted particles sticking to your tubes, radiators and other cooling components.
  • Coolant might fade over time.
その他の情報
P/N CL-W332-CU00SW-A
本体サイズ 92 L * 92.5 W * 64 H mm
インターフェース USB 2.0 connectors (9 Pin)
インターフェース Windows 7/8/8.1/10/11
入力電源 1.15 W
表示方法 2.1” TFT-LCD (IPS)
Display Resolution 480x480 (RGB) px
Compatibility Intel:LGA 1700/1200/1156/1155/1151/1150
AMD:AM5/AM4/AM3+/AM3/AM2+/AM2/FM2/FM1
Rated Voltage 5 V
Threads G ¼”
Heatsink Material CU、PMMA、ABS

User Manual

  • ファイル名
  • 概要
  • サイズ
  • Version
  • Release Date